McIntosh WK-3 El manual del propietario Pagina 6
- Pagina / 20
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
6
Installation
The CR12 can be placed upright on a table or shelf, stand-
ing on its four feet. It also can be custom installed in a
piece of furniture or cabinet of your choice. The required
panel cutout, ventilation cutout and unit dimensions are
shown.
Always provide adequate ventilation for your CR12.
Cool operation ensures the longest possible operating life
for any electronic instrument. Do not install the CR12 di-
rectly above a heat generating component such as a high
powered amplifier. If all the components are installed in a
single cabinet, a quiet running ventilation fan can be a defi-
Installation
17-1/2"
444mm
17-1/16"
433.4mm
7/32"
5.3mm
Support Shelf
Outline of Front Panel
Edge of Cutout
Panel Height
7.00"
177.8mm
6-9/16"
166.7mm
1/4"
6mm
3/16"
5.1mm
End Caps
7-1/16"
179.8mm
Bottom of Cutout and Top
of Support Shelf Must
Coincide
Mounting Surface
Outline of Unit
(Side View)
Support Shelf
Mounting Bracket at Both Sides of the Rear Panel.
Fasten with 6-32 x 3/8 Machine Screw and Washer to Chassis.
Fasten with 6 x 1/2 Wood Screw and Washer to Support Shelf
6"
15"
9"
Mounting Surface
Cut Out Center
for Ventilation
(Bottom View)
(Front View)
Cut Out Center
for Ventilation
FrontView of a CR12
custom installed
nite asset in maintaining all the system components at the
coolest possible operating temperature.
A custom cabinet installation should provide the follow-
ing minimum spacing dimensions for cool operation. Allow
at least 1-1/2 inches (3.8cm) above the unit so airflow is
not obstructed. Allow 17-1/2 inches (44.5cm) depth behind
the mounting panel, which includes clearance for connec-
tors. Allow 1-1/8 inches (2.9cm) in front of the mounting
panel for knob clearance. Be sure to cut out a ventilation
hole in the mounting shelf according to the dimensions in
the drawing.
Side View of a CR12
custom installed
Bottom View of a CR12
custom installed
- IMPORTANT SAFETY 3
- INSTRUCTIONS! 3
- Performance Features 4
- Safety Instructions cont 4
- Introduction 4
- Pre-Installation 5
- Connector Information 5
- Installation 6
- CR12 Rear Panel Controls 7
- Connections and Switches 7
- Switches 7
- How to Connect 9
- Additional CR12s 9
- How to Connect the CR12 10
- CR12 Front Panel Displays 11
- Push-Buttons and Switch 11
- How to Operate from the Front 12
- Figure 3 13
- Figure 4 13
- Figure 5 14
- HR033 Push-Buttons 16
- How to Operate HR033 17
- How to Operate the HR033 17
- Specifications 18
- Packing Instructions 19
- McIntosh Part No. 04042001 20
- McIntosh Laboratory, Inc 20
- 2 Chambers Street 20
- Binghamton, NY 13903 20
Relacionado con productos y manuales para Teclados numéricos McIntosh WK-3
Teclados numéricos McIntosh WK-3 Manual de usuario
(52 paginas)
(52 paginas)
AEG S2339-5I manuales
Manuales del propietario y guías del usuario para No AEG S2339-5I.
Ofrecemos 1 manuales en pdf AEG S2339-5I para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales